Search

TDS-16489U R2 Specification

TDS-16489U R2
Specification
Buy→

  1. TDS-16489U-SE1-R2 (Legacy)
    CPU Intel® E5-2620 v4 8-core 2.1 GHz processor x2
    *Available with customization requirement
    CPU Architecture 64-bit x86
    Floating Point Unit
    Encryption Engine (AES-NI)
    Hardware-accelerated Transcoding QTS: Optional via a PCIe graphics card
    QES: N/A
    System Memory 64GB RDIMM DDR4 (8 x 8GB)
    Maximum Memory RDIMM/LRDIMM: 1 TB (16 x 64 GB)
    Memory Slot 16 x RDIMM DDR4
    You can only use one type of dual in-line memory module (DIMM) at a time. Do not use registered DIMM (RDIMM) with load-reduction DIMM (LRDIMM) memory.
    For the memory installation guidelines, see chapter 5 of the TDS-16489U User Guide.
    Flash Memory 4GB (DOM for dual OS)
    Drive Bay Front: 16 x 3.5-inch
    Rear: 4 x 2.5-inch
    Drive Compatibility 3.5-inch bays:
    3.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS solid state drives

    2.5-inch bays:
    2.5-inch SATA/SAS solid state drives
    Hot-swappable
    SSD Cache Acceleration Support
    GPU pass-through
    SR-IOV
    Gigabit Ethernet Port (RJ45) 2
    For a list of compatible network adapters, please visit the Compatibility List.
    For instructions on how to install network adapters, please refer to Chapter 6 of the QNAP NAS Hardware Manual.
    10 Gigabit Ethernet Port 4 x 10GbE SFP+
    Wake on LAN (WOL)
    Jumbo Frame
    PCIe Slot 4
    Slot 1: PCIe Gen 3 x16
    Slot 2: PCIe Gen 3 x8
    Slot 3: PCIe Gen 3 x8
    Slot 4: PCIe Gen 3 x8
    USB 3.2 Gen 1 port 4
    IPMI 3 (LAN, VGA, console)
    *Only work with QTS OS
    Form Factor 3U Rackmount
    LED Indicators HDD 1-16, Status, 10 GbE, LAN, storage expansion port status
    Buttons Power, Reset
    Dimensions (HxWxD) 130.8 × 444 × 744 mm
    Weight (Net) 22.42 kg
    Weight (Gross) 30.19 kg
    Operating Temperature 0 - 40 °C (32°F - 104°F)
    Storage Temperature -20 - 70°C (-4°F - 158°F)
    Relative Humidity 5-95% RH non-condensing, wet bulb: 27˚C (80.6˚F)
    Power Supply Unit Redundant/ Hot Swap ATX Power Supply,Input:
    50-60 Hz
    100-127V~/ 10A
    200-240V/ 5A
    Output: 770W
    Power Consumption: Disk Standby Mode 254.21 W
    Power Consumption: Operating Mode, Typical 362.86 W
    Tested with drives fully populated.
    Fan 4 x 60mm, 12VDC
    System Warning Buzzer
    Standard Warranty 5
    Max. Number of Concurrent Connections (CIFS) - with Max. Memory 10000
    Note: Use only QNAP memory modules to maintain system performance and stability. For NAS devices with more than one memory slot, use QNAP modules with identical specifications and refer to the hardware user manual to install compatible QNAP memory modules.
    Warning: Using unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
    QNAP reserves the right to replace partial parts or accessories if the original is no longer available from its manufacturer/supplier. Any replacement would be fully tested and verified to meet strict compatibility and stability guidelines and will deliver identical performance to the original.
    The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
    Product images are for illustrative purposes only and may differ from the actual product. Due to differences in monitors, colors of products may also appear different to those shown on the site.
    Designs and specifications are subject to change without notice.

  2. TDS-16489U-SE2-R2 (Legacy)
    CPU Intel® E5-2620 v4 8-core 2.1 GHz processor x2
    *Available with customization requirement
    CPU Architecture 64-bit x86
    Floating Point Unit
    Encryption Engine (AES-NI)
    Hardware-accelerated Transcoding QTS: Optional via a PCIe graphics card
    QES: N/A
    System Memory 128GB RDIMM DDR4 (8 x 16GB)
    Maximum Memory RDIMM/LRDIMM: 1 TB (16 x 64 GB)
    Memory Slot 16 x RDIMM DDR4
    You can only use one type of dual in-line memory module (DIMM) at a time. Do not use registered DIMM (RDIMM) with load-reduction DIMM (LRDIMM) memory.
    For the memory installation guidelines, see chapter 5 of the TDS-16489U User Guide.
    Flash Memory 4GB (DOM for dual OS)
    Drive Bay Front: 16 x 3.5-inch
    Rear: 4 x 2.5-inch
    Drive Compatibility 3.5-inch bays:
    3.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS solid state drives

    2.5-inch bays:
    2.5-inch SATA/SAS solid state drives
    Hot-swappable
    SSD Cache Acceleration Support
    GPU pass-through
    SR-IOV
    Gigabit Ethernet Port (RJ45) 2
    For a list of compatible network adapters, please visit the Compatibility List.
    For instructions on how to install network adapters, please refer to Chapter 6 of the QNAP NAS Hardware Manual.
    10 Gigabit Ethernet Port 4 x 10GbE SFP+
    Wake on LAN (WOL)
    Jumbo Frame
    PCIe Slot 4
    Slot 1: PCIe Gen 3 x16
    Slot 2: PCIe Gen 3 x8
    Slot 3: PCIe Gen 3 x8
    Slot 4: PCIe Gen 3 x8
    USB 3.2 Gen 1 port 4
    IPMI 3 (LAN, VGA, console)
    *Only work with QTS OS
    Form Factor 3U Rackmount
    LED Indicators HDD 1-16, Status, 10 GbE, LAN, storage expansion port status
    Buttons Power, Reset
    Dimensions (HxWxD) 130.8 × 444 × 744 mm
    Weight (Net) 22.42 kg
    Weight (Gross) 30.19 kg
    Operating Temperature 0 - 40 °C (32°F - 104°F)
    Storage Temperature -20 - 70°C (-4°F - 158°F)
    Relative Humidity 5-95% RH non-condensing, wet bulb: 27˚C (80.6˚F)
    Power Supply Unit Redundant/ Hot Swap ATX Power Supply,Input:
    50-60 Hz
    100-127V~/ 10A
    200-240V/ 5A
    Output: 770W
    Power Consumption: Disk Standby Mode 254.21 W
    Power Consumption: Operating Mode, Typical 362.86 W
    Tested with drives fully populated.
    Fan 4 x 60mm, 12VDC
    System Warning Buzzer
    Standard Warranty 5
    Max. Number of Concurrent Connections (CIFS) - with Max. Memory 10000
    Note: Use only QNAP memory modules to maintain system performance and stability. For NAS devices with more than one memory slot, use QNAP modules with identical specifications and refer to the hardware user manual to install compatible QNAP memory modules.
    Warning: Using unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
    QNAP reserves the right to replace partial parts or accessories if the original is no longer available from its manufacturer/supplier. Any replacement would be fully tested and verified to meet strict compatibility and stability guidelines and will deliver identical performance to the original.
    The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
    Product images are for illustrative purposes only and may differ from the actual product. Due to differences in monitors, colors of products may also appear different to those shown on the site.
    Designs and specifications are subject to change without notice.

  3. TDS-16489U-SF2-R2 (Legacy)
    CPU Intel® E5-2630 v4 10-core 2.2 GHz processor x2
    *Available with customization requirement
    CPU Architecture 64-bit x86
    Floating Point Unit
    Encryption Engine (AES-NI)
    Hardware-accelerated Transcoding QTS: Optional via a PCIe graphics card
    QES: N/A
    System Memory 128GB RDIMM DDR4 (8 x 16GB)
    Maximum Memory RDIMM/LRDIMM: 1 TB (16 x 64 GB)
    Memory Slot 16 x RDIMM DDR4
    You can only use one type of dual in-line memory module (DIMM) at a time. Do not use registered DIMM (RDIMM) with load-reduction DIMM (LRDIMM) memory.
    For the memory installation guidelines, see chapter 5 of the TDS-16489U User Guide.
    Flash Memory 4GB (DOM for dual OS)
    Drive Bay Front: 16 x 3.5-inch
    Rear: 4 x 2.5-inch
    Drive Compatibility 3.5-inch bays:
    3.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS solid state drives

    2.5-inch bays:
    2.5-inch SATA/SAS solid state drives
    Hot-swappable
    SSD Cache Acceleration Support
    GPU pass-through
    SR-IOV
    Gigabit Ethernet Port (RJ45) 2
    For a list of compatible network adapters, please visit the Compatibility List.
    For instructions on how to install network adapters, please refer to Chapter 6 of the QNAP NAS Hardware Manual.
    10 Gigabit Ethernet Port 4 x 10GbE SFP+
    Wake on LAN (WOL)
    Jumbo Frame
    PCIe Slot 4
    Slot 1: PCIe Gen 3 x16
    Slot 2: PCIe Gen 3 x8
    Slot 3: PCIe Gen 3 x8
    Slot 4: PCIe Gen 3 x8
    USB 3.2 Gen 1 port 4
    IPMI 3 (LAN, VGA, console)
    *Only work with QTS OS
    Form Factor 3U Rackmount
    LED Indicators HDD 1-16, Status, 10 GbE, LAN, storage expansion port status
    Buttons Power, Reset
    Dimensions (HxWxD) 130.8 × 444 × 744 mm
    Weight (Net) 22.42 kg
    Weight (Gross) 30.19 kg
    Operating Temperature 0 - 40 °C (32°F - 104°F)
    Storage Temperature -20 - 70°C (-4°F - 158°F)
    Relative Humidity 5-95% RH non-condensing, wet bulb: 27˚C (80.6˚F)
    Power Supply Unit Redundant/ Hot Swap ATX Power Supply,Input:
    50-60 Hz
    100-127V~/ 10A
    200-240V/ 5A
    Output: 770W
    Power Consumption: Disk Standby Mode 254.21 W
    Power Consumption: Operating Mode, Typical 362.86 W
    Tested with drives fully populated.
    Fan 4 x 60mm, 12VDC
    System Warning Buzzer
    Standard Warranty 5
    Max. Number of Concurrent Connections (CIFS) - with Max. Memory 10000
    Note: Use only QNAP memory modules to maintain system performance and stability. For NAS devices with more than one memory slot, use QNAP modules with identical specifications and refer to the hardware user manual to install compatible QNAP memory modules.
    Warning: Using unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
    QNAP reserves the right to replace partial parts or accessories if the original is no longer available from its manufacturer/supplier. Any replacement would be fully tested and verified to meet strict compatibility and stability guidelines and will deliver identical performance to the original.
    The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
    Product images are for illustrative purposes only and may differ from the actual product. Due to differences in monitors, colors of products may also appear different to those shown on the site.
    Designs and specifications are subject to change without notice.

  4. TDS-16489U-SF3-R2 (Legacy)
    CPU Intel® E5-2630 v4 10-core 2.2 GHz processor x2
    *Available with customization requirement
    CPU Architecture 64-bit x86
    Floating Point Unit
    Encryption Engine (AES-NI)
    Hardware-accelerated Transcoding QTS: Optional via a PCIe graphics card
    QES: N/A
    System Memory 256GB RDIMM DDR4 (8 x 32 GB)
    Maximum Memory RDIMM/LRDIMM: 1 TB (16 x 64 GB)
    Memory Slot 16 x RDIMM DDR4
    You can only use one type of dual in-line memory module (DIMM) at a time. Do not use registered DIMM (RDIMM) with load-reduction DIMM (LRDIMM) memory.
    For the memory installation guidelines, see chapter 5 of the TDS-16489U User Guide.
    Flash Memory 4GB (DOM for dual OS)
    Drive Bay Front: 16 x 3.5-inch
    Rear: 4 x 2.5-inch
    Drive Compatibility 3.5-inch bays:
    3.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS solid state drives

    2.5-inch bays:
    2.5-inch SATA/SAS solid state drives
    Hot-swappable
    SSD Cache Acceleration Support
    GPU pass-through
    SR-IOV
    Gigabit Ethernet Port (RJ45) 2
    For a list of compatible network adapters, please visit the Compatibility List.
    For instructions on how to install network adapters, please refer to Chapter 6 of the QNAP NAS Hardware Manual.
    10 Gigabit Ethernet Port 4 x 10GbE SFP+
    Wake on LAN (WOL)
    Jumbo Frame
    PCIe Slot 4
    Slot 1: PCIe Gen 3 x16
    Slot 2: PCIe Gen 3 x8
    Slot 3: PCIe Gen 3 x8
    Slot 4: PCIe Gen 3 x8
    USB 3.2 Gen 1 port 4
    IPMI 3 (LAN, VGA, console)
    *Only work with QTS OS
    Form Factor 3U Rackmount
    LED Indicators HDD 1-16, Status, 10 GbE, LAN, storage expansion port status
    Buttons Power, Reset
    Dimensions (HxWxD) 130.8 × 444 × 744 mm
    Weight (Net) 22.42 kg
    Weight (Gross) 30.19 kg
    Operating Temperature 0 - 40 °C (32°F - 104°F)
    Storage Temperature -20 - 70°C (-4°F - 158°F)
    Relative Humidity 5-95% RH non-condensing, wet bulb: 27˚C (80.6˚F)
    Power Supply Unit Redundant/ Hot Swap ATX Power Supply,Input:
    50-60 Hz
    100-127V~/ 10A
    200-240V/ 5A
    Output: 770W
    Power Consumption: Disk Standby Mode 254.21 W
    Power Consumption: Operating Mode, Typical 362.86 W
    Tested with drives fully populated.
    Fan 4 x 60mm, 12VDC
    System Warning Buzzer
    Standard Warranty 5
    Max. Number of Concurrent Connections (CIFS) - with Max. Memory 10000
    Note: Use only QNAP memory modules to maintain system performance and stability. For NAS devices with more than one memory slot, use QNAP modules with identical specifications and refer to the hardware user manual to install compatible QNAP memory modules.
    Warning: Using unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
    QNAP reserves the right to replace partial parts or accessories if the original is no longer available from its manufacturer/supplier. Any replacement would be fully tested and verified to meet strict compatibility and stability guidelines and will deliver identical performance to the original.
    The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
    Product images are for illustrative purposes only and may differ from the actual product. Due to differences in monitors, colors of products may also appear different to those shown on the site.
    Designs and specifications are subject to change without notice.

  5. TDS-16489U-SA1-R2 (Legacy)
    CPU Intel® E5-2620 v3 6-core 2.4 GHz processor x2
    *Available with customization requirement
    CPU Architecture 64-bit x86
    Floating Point Unit
    Encryption Engine (AES-NI)
    Hardware-accelerated Transcoding QTS: Optional via a PCIe graphics card
    QES: N/A
    System Memory 64GB RDIMM DDR4 (8 x 8GB)
    Maximum Memory RDIMM/LRDIMM: 1 TB (16 x 64 GB)
    Memory Slot 16 x RDIMM DDR4
    You can only use one type of dual in-line memory module (DIMM) at a time. Do not use registered DIMM (RDIMM) with load-reduction DIMM (LRDIMM) memory.
    For the memory installation guidelines, see chapter 5 of the TDS-16489U User Guide.
    Flash Memory 4GB (DOM for dual OS)
    Drive Bay Front: 16 x 3.5-inch
    Rear: 4 x 2.5-inch
    Drive Compatibility 3.5-inch bays:
    3.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS solid state drives

    2.5-inch bays:
    2.5-inch SATA/SAS solid state drives
    Hot-swappable
    SSD Cache Acceleration Support
    GPU pass-through
    SR-IOV
    Gigabit Ethernet Port (RJ45) 2
    For a list of compatible network adapters, please visit the Compatibility List.
    For instructions on how to install network adapters, please refer to Chapter 6 of the QNAP NAS Hardware Manual.
    10 Gigabit Ethernet Port 4 x 10GbE SFP+
    Wake on LAN (WOL)
    Jumbo Frame
    PCIe Slot 4
    Slot 1: PCIe Gen 3 x16
    Slot 2: PCIe Gen 3 x8
    Slot 3: PCIe Gen 3 x8
    Slot 4: PCIe Gen 3 x8
    USB 3.2 Gen 1 port 4
    IPMI 3 (LAN, VGA, console)
    *Only work with QTS OS
    Form Factor 3U Rackmount
    LED Indicators HDD 1-16, Status, 10 GbE, LAN, storage expansion port status
    Buttons Power, Reset
    Dimensions (HxWxD) 130.8 × 444 × 744 mm
    Weight (Net) 22.42 kg
    Weight (Gross) 30.19 kg
    Operating Temperature 0 - 40 °C (32°F - 104°F)
    Storage Temperature -20 - 70°C (-4°F - 158°F)
    Relative Humidity 5-95% RH non-condensing, wet bulb: 27˚C (80.6˚F)
    Power Supply Unit Redundant/ Hot Swap ATX Power Supply,Input:
    50-60 Hz
    100-127V~/ 10A
    200-240V/ 5A
    Output: 770W
    Power Consumption: Disk Standby Mode 254.21 W
    Power Consumption: Operating Mode, Typical 362.86 W
    Tested with drives fully populated.
    Fan 4 x 60mm, 12VDC
    System Warning Buzzer
    Max. Number of Concurrent Connections (CIFS) - with Max. Memory 10000
    Note: Use only QNAP memory modules to maintain system performance and stability. For NAS devices with more than one memory slot, use QNAP modules with identical specifications and refer to the hardware user manual to install compatible QNAP memory modules.
    Warning: Using unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
    QNAP reserves the right to replace partial parts or accessories if the original is no longer available from its manufacturer/supplier. Any replacement would be fully tested and verified to meet strict compatibility and stability guidelines and will deliver identical performance to the original.
    The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
    Product images are for illustrative purposes only and may differ from the actual product. Due to differences in monitors, colors of products may also appear different to those shown on the site.
    Designs and specifications are subject to change without notice.

  6. TDS-16489U-SA2-R2 (Legacy)
    CPU Intel® E5-2620 v3 6-core 2.4 GHz processor x2
    *Available with customization requirement
    CPU Architecture 64-bit x86
    Floating Point Unit
    Encryption Engine (AES-NI)
    Hardware-accelerated Transcoding QTS: Optional via a PCIe graphics card
    QES: N/A
    System Memory 128GB RDIMM DDR4 (8 x 16GB)
    Maximum Memory RDIMM/LRDIMM: 1 TB (16 x 64 GB)
    Memory Slot 16 x RDIMM DDR4
    You can only use one type of dual in-line memory module (DIMM) at a time. Do not use registered DIMM (RDIMM) with load-reduction DIMM (LRDIMM) memory.
    For the memory installation guidelines, see chapter 5 of the TDS-16489U User Guide.
    Flash Memory 4GB (DOM for dual OS)
    Drive Bay Front: 16 x 3.5-inch
    Rear: 4 x 2.5-inch
    Drive Compatibility 3.5-inch bays:
    3.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS solid state drives

    2.5-inch bays:
    2.5-inch SATA/SAS solid state drives
    Hot-swappable
    SSD Cache Acceleration Support
    GPU pass-through
    SR-IOV
    Gigabit Ethernet Port (RJ45) 2
    For a list of compatible network adapters, please visit the Compatibility List.
    For instructions on how to install network adapters, please refer to Chapter 6 of the QNAP NAS Hardware Manual.
    10 Gigabit Ethernet Port 4 x 10GbE SFP+
    Wake on LAN (WOL)
    Jumbo Frame
    PCIe Slot 4
    Slot 1: PCIe Gen 3 x16
    Slot 2: PCIe Gen 3 x8
    Slot 3: PCIe Gen 3 x8
    Slot 4: PCIe Gen 3 x8
    USB 3.2 Gen 1 port 4
    IPMI 3 (LAN, VGA, console)
    *Only work with QTS OS
    Form Factor 3U Rackmount
    LED Indicators HDD 1-16, Status, 10 GbE, LAN, storage expansion port status
    Buttons Power, Reset
    Dimensions (HxWxD) 130.8 × 444 × 744 mm
    Weight (Net) 22.42 kg
    Weight (Gross) 30.19 kg
    Operating Temperature 0 - 40 °C (32°F - 104°F)
    Storage Temperature -20 - 70°C (-4°F - 158°F)
    Relative Humidity 5-95% RH non-condensing, wet bulb: 27˚C (80.6˚F)
    Power Supply Unit Redundant/ Hot Swap ATX Power Supply,Input:
    50-60 Hz
    100-127V~/ 10A
    200-240V/ 5A
    Output: 770W
    Power Consumption: Disk Standby Mode 254.21 W
    Power Consumption: Operating Mode, Typical 362.86 W
    Tested with drives fully populated.
    Fan 4 x 60mm, 12VDC
    System Warning Buzzer
    Max. Number of Concurrent Connections (CIFS) - with Max. Memory 10000
    Note: Use only QNAP memory modules to maintain system performance and stability. For NAS devices with more than one memory slot, use QNAP modules with identical specifications and refer to the hardware user manual to install compatible QNAP memory modules.
    Warning: Using unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
    QNAP reserves the right to replace partial parts or accessories if the original is no longer available from its manufacturer/supplier. Any replacement would be fully tested and verified to meet strict compatibility and stability guidelines and will deliver identical performance to the original.
    The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
    Product images are for illustrative purposes only and may differ from the actual product. Due to differences in monitors, colors of products may also appear different to those shown on the site.
    Designs and specifications are subject to change without notice.

  7. TDS-16489U-SB2-R2 (Legacy)
    CPU Intel® E5-2630 v3 8-core 2.4 GHz processor x2
    *Available with customization requirement
    CPU Architecture 64-bit x86
    Floating Point Unit
    Encryption Engine (AES-NI)
    Hardware-accelerated Transcoding QTS: Optional via a PCIe graphics card
    QES: N/A
    System Memory 128GB RDIMM DDR4 (8 x 16GB)
    Maximum Memory RDIMM/LRDIMM: 1 TB (16 x 64 GB)
    Memory Slot 16 x RDIMM DDR4
    You can only use one type of dual in-line memory module (DIMM) at a time. Do not use registered DIMM (RDIMM) with load-reduction DIMM (LRDIMM) memory.
    For the memory installation guidelines, see chapter 5 of the TDS-16489U User Guide.
    Flash Memory 4GB (DOM for dual OS)
    Drive Bay Front: 16 x 3.5-inch
    Rear: 4 x 2.5-inch
    Drive Compatibility 3.5-inch bays:
    3.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS solid state drives

    2.5-inch bays:
    2.5-inch SATA/SAS solid state drives
    Hot-swappable
    SSD Cache Acceleration Support
    GPU pass-through
    SR-IOV
    Gigabit Ethernet Port (RJ45) 2
    For a list of compatible network adapters, please visit the Compatibility List.
    For instructions on how to install network adapters, please refer to Chapter 6 of the QNAP NAS Hardware Manual.
    10 Gigabit Ethernet Port 4 x 10GbE SFP+
    Wake on LAN (WOL)
    Jumbo Frame
    PCIe Slot 4
    Slot 1: PCIe Gen 3 x16
    Slot 2: PCIe Gen 3 x8
    Slot 3: PCIe Gen 3 x8
    Slot 4: PCIe Gen 3 x8
    USB 3.2 Gen 1 port 4
    IPMI 3 (LAN, VGA, console)
    *Only work with QTS OS
    Form Factor 3U Rackmount
    LED Indicators HDD 1-16, Status, 10 GbE, LAN, storage expansion port status
    Buttons Power, Reset
    Dimensions (HxWxD) 130.8 × 444 × 744 mm
    Weight (Net) 22.42 kg
    Weight (Gross) 30.19 kg
    Operating Temperature 0 - 40 °C (32°F - 104°F)
    Storage Temperature -20 - 70°C (-4°F - 158°F)
    Relative Humidity 5-95% RH non-condensing, wet bulb: 27˚C (80.6˚F)
    Power Supply Unit Redundant/ Hot Swap ATX Power Supply,Input:
    50-60 Hz
    100-127V~/ 10A
    200-240V/ 5A
    Output: 770W
    Power Consumption: Disk Standby Mode 254.21 W
    Power Consumption: Operating Mode, Typical 362.86 W
    Tested with drives fully populated.
    Fan 4 x 60mm, 12VDC
    System Warning Buzzer
    Max. Number of Concurrent Connections (CIFS) - with Max. Memory 10000
    Note: Use only QNAP memory modules to maintain system performance and stability. For NAS devices with more than one memory slot, use QNAP modules with identical specifications and refer to the hardware user manual to install compatible QNAP memory modules.
    Warning: Using unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
    QNAP reserves the right to replace partial parts or accessories if the original is no longer available from its manufacturer/supplier. Any replacement would be fully tested and verified to meet strict compatibility and stability guidelines and will deliver identical performance to the original.
    The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
    Product images are for illustrative purposes only and may differ from the actual product. Due to differences in monitors, colors of products may also appear different to those shown on the site.
    Designs and specifications are subject to change without notice.

  8. TDS-16489U-SB3-R2 (Legacy)
    CPU Intel® E5-2630 v3 8-core 2.4 GHz processor x2
    *Available with customization requirement
    CPU Architecture 64-bit x86
    Floating Point Unit
    Encryption Engine (AES-NI)
    Hardware-accelerated Transcoding QTS: Optional via a PCIe graphics card
    QES: N/A
    System Memory 256GB RDIMM DDR4 (8 x 32 GB)
    Maximum Memory RDIMM/LRDIMM: 1 TB (16 x 64 GB)
    Memory Slot 16 x RDIMM DDR4
    You can only use one type of dual in-line memory module (DIMM) at a time. Do not use registered DIMM (RDIMM) with load-reduction DIMM (LRDIMM) memory.
    For the memory installation guidelines, see chapter 5 of the TDS-16489U User Guide.
    Flash Memory 4GB (DOM for dual OS)
    Drive Bay Front: 16 x 3.5-inch
    Rear: 4 x 2.5-inch
    Drive Compatibility 3.5-inch bays:
    3.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS hard disk drives
    2.5-inch SATA/SAS solid state drives

    2.5-inch bays:
    2.5-inch SATA/SAS solid state drives
    Hot-swappable
    SSD Cache Acceleration Support
    GPU pass-through
    SR-IOV
    Gigabit Ethernet Port (RJ45) 2
    For a list of compatible network adapters, please visit the Compatibility List.
    For instructions on how to install network adapters, please refer to Chapter 6 of the QNAP NAS Hardware Manual.
    10 Gigabit Ethernet Port 4 x 10GbE SFP+
    Wake on LAN (WOL)
    Jumbo Frame
    PCIe Slot 4
    Slot 1: PCIe Gen 3 x16
    Slot 2: PCIe Gen 3 x8
    Slot 3: PCIe Gen 3 x8
    Slot 4: PCIe Gen 3 x8
    USB 3.2 Gen 1 port 4
    IPMI 3 (LAN, VGA, console)
    *Only work with QTS OS
    Form Factor 3U Rackmount
    LED Indicators HDD 1-16, Status, 10 GbE, LAN, storage expansion port status
    Buttons Power, Reset
    Dimensions (HxWxD) 130.8 × 444 × 744 mm
    Weight (Net) 22.42 kg
    Weight (Gross) 30.19 kg
    Operating Temperature 0 - 40 °C (32°F - 104°F)
    Storage Temperature -20 - 70°C (-4°F - 158°F)
    Relative Humidity 5-95% RH non-condensing, wet bulb: 27˚C (80.6˚F)
    Power Supply Unit Redundant/ Hot Swap ATX Power Supply,Input:
    50-60 Hz
    100-127V~/ 10A
    200-240V/ 5A
    Output: 770W
    Power Consumption: Disk Standby Mode 254.21 W
    Power Consumption: Operating Mode, Typical 362.86 W
    Tested with drives fully populated.
    Fan 4 x 60mm, 12VDC
    System Warning Buzzer
    Max. Number of Concurrent Connections (CIFS) - with Max. Memory 10000
    Note: Use only QNAP memory modules to maintain system performance and stability. For NAS devices with more than one memory slot, use QNAP modules with identical specifications and refer to the hardware user manual to install compatible QNAP memory modules.
    Warning: Using unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
    QNAP reserves the right to replace partial parts or accessories if the original is no longer available from its manufacturer/supplier. Any replacement would be fully tested and verified to meet strict compatibility and stability guidelines and will deliver identical performance to the original.
    The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
    Product images are for illustrative purposes only and may differ from the actual product. Due to differences in monitors, colors of products may also appear different to those shown on the site.
    Designs and specifications are subject to change without notice.
  1. Operating System

    QES 2.2.1
    Supported Languages

    Chinese (Traditional & Simplified), Czech, Danish, Dutch, English, Finnish, French, German, Greek, Hungarian, Italian, Japanese, Korean, Norwegian, Polish, Portuguese (Brazil), Romanian, Russian, Spanish, Swedish, Thai, Turkish
    Storage Pool

    Shared Folder Type

    Thick, Thin
    JBOD Expansion

    Fibre Channel Service

    LUN Type

    Thick, Thin
    Storage QoS

    Storage Management
    1. NVRAM write cache (BBU-protected)
    2. Scheduled Backup Battery Unit (BBU) learning
    3. Pool scrub for data verification
    4. Share folder quota management
    5. Inline deduplication for shared folder/LUN
    6. Inline compression for shared folder/LUN
    7. Inline encryption for shared folder/LUN
    8. WORM (Write Once Read Many) for shared folder
    9. Online pool, share folder, and LUN expansion
    10. Time-Limited Error Recovery (TLER)
    11. JBOD ID Reinitialized
    12. Support optional fibre channel
    13. Support expanding the capacity of the storage pool by replacing the disks with larger ones
    Show more...
    RAID Type

    RAID 0, 1, 5, 6, 10, 50, 60, RAID TP, triple Mirror
    RAID Group

    To ensure data security, system stability, and storage performance, the maximum number of drives for a single RAID group is now 16 (applicable to RAID 5, RAID 6, RAID TP, and subgroups of RAID 50 and RAID 60). Nevertheless, users can combine multiple RAID groups into a large storage pool that contains more than 16 drives, using RAID 50, RAID 60, or RAID 10 as the RAID configuration. This enhancement will only be applied to new RAID groups. All existing RAID groups and storage systems will not be affected.
    RAID Hot Spare

    Global, Local
    End-to-End data integrity

    Silent error detection and self-healing

    Internal drive

    ZFS
    Disk S.M.A.R.T. Scan

    Disk S.M.A.R.T. Data Migration

    SSD Trim

    SSD Life Estimation

    Shared Folder Snapshot

    LUN Snapshot

    Backup Station
    1. Remote replication server over Rsync
    2. Remote replication server over SnapSync
    3. Real-time or scheduled replication over SnapSync
    4. Compression and Dedupication over SnapSync
    5. Support Veeam Backup & Replication
    Show more...
    File Server
    1. Shared folder for CIFS/SMB, NFS and FTP
    2. File sharing across Windows, Mac, and Linux/UNIX
    3. Windows ACL
    FTP Server
    1. FTP over SSL/TLS (Explicit)
    2. FXP support
    3. Passive ftp port range control
    Access Right Management
    1. Batch users creation
    2. Import/Export users
    3. User quota management
    4. Local user access control for CIFS/SMB and FTP
    Domain Authentication Integration
    1. Microsoft Active Directory support
    2. LDAP client
    3. Domain users login via CIFS/SMB, FTP
    Resource Monitor

    SNMP

    V1, V2, V3
    Network recycle bin

    Network recycle bin for file deletion via CIFS/SMB, File Station and FTP
    System Log & Notification Center
    1. System Log: Yes
    2. Notification Center: -
    Smart Fan

    Administration
    1. Smart file filter
    2. Comprehensive logs (events & connection)
    3. Syslog client management
    4. System settings backup and restore
    5. Command Line Interface (CLI)
    Show more...
    Internet protocol

    IPv4 & IPv6
    10 Gigabit NICs with jumbo frame

    LACP, Load Balance, Failover, Round Robin
    Protocols

    CIFS/SMB2/SMB3, NFS v3/NFS v4.1, FTP, FTPS, TFTP, HTTP, HTTPS, SSH, iSCSI, Fibre Channel, SNMP, SMTP, and SMSC
    iSER

    (iSCSI Extensions for RDMA)
    Bonjour Discovery

    Network access protection with auto-blocking

    SSH, HTTP(S), FTP, CIFS/SMB
    CIFS/SMB host access control for shared folders

    AES 256-bit Volume Encryption validated by FIPS 140-2 CAVP

    AES 256-bit Folder Encryption validated by FIPS 140-2 CAVP

    2-step verification

    Service binding

    (based on network interfaces)
    Importable SSL certificates

    HA Manager

    Fail-over

    Rolling Update

    VMware vSphere Ready

    Windows Server certifcated

    Citrix Ready

    Thirty Party Plug-ins
    1. SMI-S Provider
    2. vSphere Web Client Plugin​
    3. VAAI Plug-in (Compatible with ESXi 8): NFS, iSCSI
    4. VMware Storage Replication Adapter (SRA)
    5. QNAP Cinder Driver for Openstack block storage
    6. QNAP Manila Driver for Openstack shared file storage
    Show more...
    PC Utilities
    1. Qfinder Pro: Windows, Mac, Linux
    2. myQNAPcloud Connect: Windows
    3. Snapshot agent for Windows VSS and VMware
    4. Qutil (MPIO command line tool for QES)
Note:
QTS does not support DRM content and some IPv6 services.
Some data encryption features may be unavailable because of country-specific legislative restrictions.
Some features may vary by model.
Designs and specifications are subject to change without notice.
TDS-16489U R2

TDS-16489U R2

Ethernet Cable x 2

Ethernet Cable x 2

Power Cord x 2

Power Cord x 2

Flat head screw x 64 (for 3.5

Flat head screw x 64 (for 3.5" HDD)

Flat head screw x 64 (for 2.5

Flat head screw x 64 (for 2.5" HDD)

Quick Installation Guide (QIG)

Quick Installation Guide (QIG)

Optional Accessories

  1. QM2-4P-384
    QM2-4P-384
    PWR-PSU-770W-DT01
    PWR-PSU-770W-DT01 (EOL)
    SCR-HDD25A-96
    SCR-HDD25A-96
    SP-SSECX79-TRAY
    SP-SSECX79-TRAY
    SP-X79U-TRAY
    SP-X79U-TRAY
    RAIL-A03-57
    RAIL-A03-57
    QXG-10G2T-X710
    QXG-10G2T-X710
    QXP-1620S-B3616W
    QXP-1620S-B3616W (EOL)
    QXP-16G2FC
    QXP-16G2FC
    QXP-32G2FC
    QXP-32G2FC
    TRX-10GSFP-SR-MLX
    TRX-10GSFP-SR-MLX
    CAB-DAC15M-SFPP
    CAB-DAC15M-SFPP
    CAB-DAC30M-SFPP
    CAB-DAC30M-SFPP
    CAB-DAC50M-SFPP
    CAB-DAC50M-SFPP
    CAB-NIC40G30M-QSFP
    CAB-NIC40G30M-QSFP
    RAM-16GDR4ECT0-RD-2400
    RAM-16GDR4ECT0-RD-2400
    RAM-32GDR4ECT0-RD-2133
    RAM-32GDR4ECT0-RD-2133 (EOL)
    RAM-8GDR4ECT0-RD-2400
    RAM-8GDR4ECT0-RD-2400
    RAM-32GDR4ECS0-LR-2400
    RAM-32GDR4ECS0-LR-2400 (EOL)
  2. QM2-2P-344
    QM2-2P-344 (EOL)
    QM2-2P-344A
    QM2-2P-344A
    QM2-2P-384
    QM2-2P-384 (EOL)
    QM2-2P-384A
    QM2-2P-384A
    QM2-2P2G2T
    QM2-2P2G2T
    QM2-4P-384
    QM2-4P-384
    QDA-A2AR
    QDA-A2AR
    QDA-A2MAR
    QDA-A2MAR
    LAN-10G2SF-MLX
    LAN-10G2SF-MLX (EOL)
    LAN-10G2T-X550
    LAN-10G2T-X550 (EOL)
    LAN-40G2SF-MLX
    LAN-40G2SF-MLX (EOL)
    QXG-10G1T
    QXG-10G1T
    QXG-10G2T-107
    QXG-10G2T-107 (EOL)
    QXG-10G2T-X710
    QXG-10G2T-X710
    QXG-25G2SF-CX6
    QXG-25G2SF-CX6
    QXG-2G1T-I225
    QXG-2G1T-I225
    QXG-2G2T-I225
    QXG-2G2T-I225
    QXG-2G4T-I225
    QXG-2G4T-I225
    QXG-5G1T-111C
    QXG-5G1T-111C
    QXG-5G2T-111C
    QXG-5G2T-111C
    QXG-5G4T-111C
    QXG-5G4T-111C
    PWR-PSU-770W-DT01
    PWR-PSU-770W-DT01 (EOL)
    SCR-HDD25A-96
    SCR-HDD25A-96
    SP-SSECX79-TRAY
    SP-SSECX79-TRAY
    SP-X79U-TRAY
    SP-X79U-TRAY
    RAIL-A03-57
    RAIL-A03-57
    QXP-1620S-B3616W
    QXP-1620S-B3616W (EOL)
    QXP-16G2FC
    QXP-16G2FC
    QXP-32G2FC
    QXP-32G2FC
    QXP-820S-B3408
    QXP-820S-B3408
    USB-U31A2P01
    USB-U31A2P01 (EOL)
    TRX-10GSFP-SR-MLX
    TRX-10GSFP-SR-MLX
    TRX-16GFCSFP-SR
    TRX-16GFCSFP-SR
    TRX-25GSFP28-SR
    TRX-25GSFP28-SR
    TRX-32GFCSFP-SR
    TRX-32GFCSFP-SR
    CAB-DAC15M-SFP28
    CAB-DAC15M-SFP28
    CAB-DAC15M-SFPP
    CAB-DAC15M-SFPP
    CAB-DAC30M-SFP28
    CAB-DAC30M-SFP28
    CAB-DAC30M-SFPP
    CAB-DAC30M-SFPP
    CAB-DAC50M-SFPP
    CAB-DAC50M-SFPP
    CAB-NIC40G30M-QSFP
    CAB-NIC40G30M-QSFP
    CAB-SAS05M-8644
    CAB-SAS05M-8644
    CAB-SAS05M-8644-8088
    CAB-SAS05M-8644-8088
    CAB-SAS10M-8644
    CAB-SAS10M-8644
    CAB-SAS10M-8644-8088
    CAB-SAS10M-8644-8088
    CAB-SAS20M-8644
    CAB-SAS20M-8644
    CAB-SAS20M-8644-8088
    CAB-SAS20M-8644-8088
    CAB-SAS30M-8644
    CAB-SAS30M-8644
    CAB-SAS30M-8644-8088
    CAB-SAS30M-8644-8088
    RAM-16GDR4ECT0-RD-2400
    RAM-16GDR4ECT0-RD-2400
    RAM-32GDR4ECT0-RD-2133
    RAM-32GDR4ECT0-RD-2133 (EOL)
    RAM-8GDR4ECT0-RD-2400
    RAM-8GDR4ECT0-RD-2400
    RAM-32GDR4ECS0-LR-2400
    RAM-32GDR4ECS0-LR-2400 (EOL)
Bundled accessories delivered together with the product such as expansion cards, power adapter, and accessories are covered with one-year warranty.

Choose specification

      Show more Less

      This site in other countries/regions:

      open menu
      back to top